[set bevat].
Eenheid lichaam
Elektro kraan X 1
Dubbelzijdige tape X 1
Stropdas wikkels x 2
Losse tie-wraps X 2
Alleen DC12V
[Maximale uitgangsstroom: 20 A
Geschat op 7.5AX2
Geschat 5AX1
[Lichaamsgrootte] Lengte 42mm X Breedte 26mm X Dikte 32mm
*Er is een geval dat er een specificatiewijziging van de grondstof is door het gemak van de fabrikant. Begrijp alsjeblieft.
[Gebruiksaanwijzing]
1, Dit product is een product voor algemeen gebruik voor DC12V voertuigen.
Afhankelijk van de specificaties van het voertuig en de elektrische onderdelen is het product mogelijk niet geschikt voor gebruik.
Wij kunnen geen garantie geven tegen storingen of defecten van de gebruikte elektrische onderdelen.
In sommige voertuigen detecteert de ECU de spanning wanneer de motor wordt gestart en vervolgens wordt de motor gestart. Controleer voor gebruik.
2, De totale maximale stroom van dit product is 20A.
De maximaal toelaatbare stroom bedraagt 7,5AX2 en 5AX1.
(De aanbevolen stroomsterkte is 4,0A X2 en 2,5AX1. Controleer voor gebruik de maximale stroomsterkte en specificatie van uw elektrische apparatuur en de specificatie van de accu van het voertuig. De output zal de accu en de stroomopwekkingscapaciteit van het voertuig niet overschrijden.
3,De aansluiting van dit product wordt gemaakt met CA/CB104 guillotine (4.0mm).
Krimp de bedrading stevig met een elektrische tang of iets dergelijks aan de guillotineterminal.
Zorg ervoor dat de aansluitingen op de guillotine-aansluitingen goed vastzitten.
*De verbinding moet worden gemaakt met een connector met een diameter van 4,0 mm (CA/CB104).
4, De hoofd unit is waterdicht.
Let op de bevestigingspunten om kortsluiting bij de aansluitingen te voorkomen.
Dit product is uitgerust met een ingebouwd beveiligingscircuit (PTC-thermistor), dat defect kan raken als de stroom het beveiligingscircuit overschrijdt.
In geval van kortsluiting wordt het circuit tijdelijk onderbroken.
5,In geval van kortsluiting, overstroom of piekstroom kan het circuit worden hersteld door het toestel enkele seconden te laten staan om af te koelen.
Identificeer en verhelp de oorzaak van de kortsluiting.
Doet u dit niet, dan kan er brand ontstaan.
6, De PTC thermistor onderbreekt de stroom door de hoeveelheid warmte die door de weerstand van de stroom wordt opgewekt.
In geval van activering van het beveiligingscircuit moeten de elektrische componenten zo spoedig mogelijk worden losgekoppeld.
Bij ongewijzigd gebruik bestaat het risico van vervorming of ontbinding van het toestel.
Het toestel mag niet worden geïnstalleerd op een plaats waar de hitte van de motor de temperatuur van het toestel doet oplopen tot meer dan 80°C.
De stroom kan onderbroken worden en het toestel kan onbruikbaar worden.
7,Voortdurend gebruik van elektrische apparatuur zonder de motor te starten kan de accu leeg laten lopen.
Het is raadzaam het even te controleren of het te gebruiken met draaiende motor.
Het is raadzaam alle elektrische apparatuur uit te schakelen alvorens de motor te starten.
8,Het gebruik van startkabels of snelladers bij het opladen van de batterij kan ertoe leiden dat het toestel smelt of defect raakt.
9, Als u dit product met veel elektrische onderdelen gebruikt, raakt de batterij leeg.
In de winter zal de accu, als hij voortdurend wordt ontladen, zonder stroom komen te zitten, dus is het raadzaam dagelijks onderhoud en spanningscontrole uit te voeren.
Voor spanningscontrole wordt aanbevolen om de batterij-checker van Kijima (304-6261) samen te gebruiken.
Houd er rekening mee dat de lithium-ionbatterij mogelijk niet volledig wordt opgeladen als de spanning onder een bepaald niveau daalt.
10. Gebruik tijdens het installatieproces een tester om de installatie te controleren.
11.Zorg ervoor dat u de negatieve draad isoleert met vinyltape enz., omdat er kortsluiting ontstaat als het stalen deel in contact komt met de connector van de negatieve draad die niet op het apparaat is aangesloten.
12, Indien het hoofdtoestel uitschakelt na het in acht nemen van het bovenstaande, gelieve de te gebruiken elektrische componenten te selecteren of de elektrische componenten naar een andere plaats over te brengen.
13, Zet altijd de hoofdschakelaar uit als je werkt. Steek geen draden in of verwijder ze niet met de hoofdsleutel in de stand ON.
Kortsluiting of andere schade aan de apparatuur kan het gevolg zijn.
De werkzaamheden moeten worden uitgevoerd op een vlakke ondergrond met het voertuig gestabiliseerd, aangezien het gevaarlijk is als het voertuig tijdens het gebruik valt.
[Set components]
・Unit body
・Electro Tap x 1
・Double sided tape x 1
・Cable Tie x 2
・Release Cable Ties x 2
・DC12V only
[Maximum output current] 20A
・Rated at 7.5A x 2
・Rated 5A x 1
[Body size] Length: 42mm x Width: 26mm x Thickness: 32mm
*There may be changes in product specifications due to the manufacturer's reasons.
[Instructions for use]
1, This is a universal product for DC12V vehicles.
This product may not be used depending on the specifications of the vehicle or electrical components.
The malfunction or failure of the electrical components which have already used are not compensated.
In some vehicles which the ECU detects the voltage to start the engine, mulfunction will be arised.Please check before use.
2, The total maximum current of this product is 20A.
The maximum allowable current is rated 7.5A x 2 and 5A x 1.
(The recommended current is 3 systems of 4.0A x 2 and 2.5A x 1.Please confirm the maximum current and specifications of the electrical components used and the specifications of the battery in the vehicle before use.The output will not exceed the battery and power generation capacity of the vehicle.
3, The connection part of this product uses CA / CB104 crimp terminal (4.0mm).
Do wiring step by step. Peel off the coating of wires, and crimp them using the pliers and bond them to the crimp terminal.
Be sure to securely connect the crimp terminals.
*Use crimp terminal & Φ4.0 (CA / CB104) for connection.
4,The main unit is waterproof.
Please pay attention to the installation point to avoid short-circuit at the connection part.
This product is equipped with a built-in protection circuit (PTC thermistor) because it may fail when an overcurrent exceeding the protection circuit flows.
In case of short circuit, the circuit is temporarily shut down.
5. In cases that the current flow shut due to short-circuit, over-current or surge, the circuit will be recovered by cooling the unit for a few seconds.
Identify the cause of the short circuit and improve the problem.
If the cause of the problem is left unattended, it may cause a fire.
6. PTC thermistor interrupts the current by the heat quantity caused by the resistance of the current.
If the protection circuit is activated, remove the electrical components immediately.
If you use it as it is, there is a possibility that the main body will be deformed or dissolved.
Do not install the unit in a place where the temperature of the unit will rise above 80°C due to engine heat.
The current may be cut off and the device may become unusable.
7. Continued use of electrical components without starting the engine may cause the battery to run out.
Please check it for a short time or use it with the engine running.
It is recommended to switch off the electrical components before starting the engine.
8. If you use a booster cable or a quick battery charger when the battery runs out of power or when charging the battery, there is a possibility that the unit will melt or break down.
9. A lot of electrical components using with this product will cause the battery exhaution.
If the battery continues to be discharged in winter, the battery will run out, so please perform daily maintenance and voltage control.
It is recommended to use Kijima's battery checker (304-6261) for voltage control.
In addition, there is a possibility that the lithium-ion battery is insufficiently charged when the voltage drops below a certain level according to the specifications.
10, Please use a tester to check the installation.
11, Be sure to insulate the negative wire with vinyl tape, etc., as it will short-circuit if the wire and the iron part touchs each other.
12, If the main unit shuts down after observing the above, select the electrical components to be used or relocate the electrical components to another location.
13, Always turn off the main key during operation.Do not plug or unplug the wires with the main key in the ON position.
There is a possibility of equipment failure due to a short circuit.
It is dangerous if the vehicle body falls down during operation, so work on a level surface with the vehicle body stable.