Used for Master Cylinder of GALE SPEED
I made the tank a GALE SPEED but it doesn't seem to mount horizontally & hellip;
I don't have a problem with it, but maybe it's my methodical nature that bothers me, so I'll bend and adjust it at a later date.
购买它我是和brembo s50大油杯使用,安装角度需要自己调整好,否则它是倾斜的。在和s50油杯配合使用上不适合安装原厂的厚垫片,厚的垫片会导致底部的螺母拧紧的空间不足,建议使用薄垫片安装,外观上没有什么好说的,总体来说是个不错的产品,简洁易安装。View Detail
Brembo RCS brake master cylinder and smoke tank (S50) I used it to install the
Smoke tank and 8mm high rubber bushings (POSH H-Shaped Rubber PARTS-NO,100202) The combination of the attached M6x20mm bolts and SPL washers does not allow for the use of the nut Do not use an SPL washer and use a normal thin washer because the cling will be reduced I did
After tightening the stay with the mirror, temporarily place the tank and check the level It was slightly tilted, so I corrected it The correction was done by putting the duct tape on the monkey wrench to prevent scratches
We were able to set up the tank well without being distracting in a good wayView Detail
TDM900 with YZF-R1's semi-radial master and Ninja H2's I used it when I assembled the Reserver tank
The length and angle are just right, but if you put the Tank on top of the Bracket, it's too high So I decided to fix it on the bottom side as shown in the picture I'm not so good at bending the bracket
This will lower the position of the tank by about 1.5 cm and it looks good
It's twice the price of a DAYTONA bracket, but it fits in just like an OEM Personally, I'm glad I chose this one because it'sView Detail
I tried installing it and it fell into the state just as I thought. Subtle bend Length If I knew it earlier I could use it elsewhere. Manufacturer is daringly aiming to make it.View Detail
I bought Nisshin's Master cylinder to install the reservoir Tank of Ninja H2.
【What made you decide the purchase?】
I found an article in Nisshin 's Master cylinder that made up Ninja H2' s reservoir tank in a certain blog, so I bought this Bracket according to the information on that blog.
【How was it actually used?】
In Bracket which made plate-like Aluminum standardized in Nisshin's Master cylinder L-shaped, if you slant the Master cylinder, the reservoir Tank will also be inclined together, but if this is a Bracket Bracket itself has a slope on the MASTER side so that even if the master cylinder is tilted it is possible to keep the reservoir Tank level.
Since there is a negative pressure in reservoir tank, even if tank reservoir Tank itself is somewhat inclined, there is no particular harm, but at least if it means to make it look better at least it is not a significant Bracket for Large Is not it?.
【Mounting was difficult?】
Just remove Bolt and Nut and replace it so anyone can easily install it as long as there are tools.
【Please tell me the installation point and hang】
As with me, when you exchange reservoir tank together, I think that once you have decided all the positions and inclination angles and final tighten it will not be a hassle twice.
[Is there anything I was disappointed about?]
nothing special
【Hope for Manufacturer - Please let me know if you have any improvement points]
I think that it will be in an expensive category if it is considered as BracketSingle Body.
If it is a little cheaper it will be easier to buy.
【Have you compared items?】
nothing special
[Others]
Is not it essential to install OEM reservoir tank of Ninja H2 which is recent CustomTrend.
Besides this Bracket
- Posh H Type Rubber 100202
We made it using.
Even if you would like to organize brembo's Tank even for non-Ninja H2, I think that it's also ant to collaborate using this Bracket.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING