44.05 EUR
(7,212 JPY)
3 (1 alle Reviews)
Past bij:
HONDA , HONDA , HONDA , HONDA CBR250R MC17, HONDA
View more
rating breakdown
5 Stars |
|
0 |
4 Stars |
|
0 |
3 Stars |
|
1 |
2 Stars |
|
0 |
1 Stars |
|
0 |
Average
It was more subtle than I expectedThe Material is more than I expected, and Bar End is a spec. that cannot be put in well It was a little bit of a loss for me personally because the material was more than I thought it would be and the Bar End was a spec
The Handlebaretc. should still be solid
Most Viewed Reviews Of RISE CORPORATION Clip-on Handlebars
Excellent
Custom HandlebarsThis custom handlebar is a perfect addition to any custom scooter build you may have. These are easy to install, excellent quality and functionality. Highly recommend for custom look.View Detail
Excellent
Cospa is nice.[How is it used?
Used for HORNET 900.
Was the installation difficult?
If you can replace the Pipe Handlebar, you can do it.
How was your experience with it?
I like the flexibility of the Position.
Aperture angle, height, and width can be adjusted.
The texture is very high.View Detail
Very Good
More room to play!I don't take myself too seriously. Just kidding. I bought this to play with Separate Handlebars.
Both the texture and the accuracy of the parts are good, but as mentioned in other reviews, I'm a little worried that I might over-tighten the screw and blunt the mountain.
You can enjoy detailed position changes in the FrontNORMAL state, relatively easy to install, changes the ride and appearance, and has expanded the range of play.
It's pricey though, so I'm wondering if I could have used another 7,000 yen item from Rakuten or Amazon.
If you buy DAYTONA's Separate handle bar, I think it will be able to support Large抵Motorcycle.View Detail
Very Good
It's a great cosmeticAround Handlebar, the setup is done I'm sure you will get used to it
To this day, the STD Handlebar is too wide for me to ride as it is and
It was too low and I couldn't help myself and finally replaced it
But, please, a farmer who claims to be a servant? Or life! (That's pretty old.)
This is my personal opinion Please understand that this is just my personal opinion
Separate handle "Pseudo It is
Fortunately, I did not have to replace the Harnesses It became possible to adjust the aperture, height, and width, so I'll try it while looking for a compromise for a while I think
However, it will never pass inspection as it is, and you will have to make structural changes at a later date
I have to..
This is so messy, isn't it?
O-Small spending, and it's all gone
Center bar is a DaytonACut Out Straight Bar for Separate Handle is diverted
The holes in the Switch box needed to be reopened, as it is an Universal Product It can't be helped
The bar end cap needs to be cut about 1cm shorter than the rubberView Detail
Very Good
Easy Separate handle possibleInstallation is quite easy as you can remove Separate handle without removing Top Bridge or Fork.
Since the pseudo-Fork is Start from the clamp height, the starting point of the Handlebar becomes high, but it may be Offset, so it can be set much better than the Sports by adjusting the drooping angle.
If the center bar is short and the width of the clamp is 10 cm or more, it is impossible to attach a pon, so I replaced the straight bar of DAYTONA.
I think that the thing itself is good, but Screw fixing the pseudo-Fork is too long and it is not good so I am changing the size.
Accuracy is a little bit, but there are places where it can not be completely fixed unless it is quite closed, so it may be that the Screw hole is going to be lost if Chosoku Position is changed frequently.
Z1000 (Type 2) There is no Clearance to attach Separate handle with Fork so we arrive at the Position that is familiar with Rear Sets gradually and are satisfied with LargeView Detail
Other Reviews From Japanese Webike user
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING