-
alle Reviews
-
Bates Light Bracket
Dit product is verwijderd of momenteel niet beschikbaar.
Excellent
Bates Light BracketI used it to install the Bates Headlight
I'm lucky that it's an OutletSale
It's just like drilling a hole in the aluminum block and cutting a screw It's a Large oddity in its own right, and it's vaguely expensive to buy
This time, I installed the Bates Headlight on the Front fork of the SUPER CUB Adopted for
The Bates Headlight itself is something I had at home, but I lost the Parts for this part I was having trouble putting it away
It's something you're selling
The width of the Bates Headlight side was a little bit narrower, but the plastic hammer I slammed it in with lol
Also, the Bolt's standard is American (or is it called Cruiser now?) I think it was the Inch standard for this
The side hole to fix the Bates Headlight was fixed with the Bolt of M10 It was a bit tight, so I wonder if it is for the 3/8Inch Bolts? I think
The one to be fixed to the fork is also probably for the 3/8 Inch Bolt
Screws were cut on this one, but the holes in the front fork of the SUPER CUB are M8 I ignored the Bolt holes and made it a PenetratingBolt because of the parallelism
I let him chew on a Large-Temple Flat Washer just in case
Because it seems to be a cut-out from the aluminum block, if you close it tightly, you will be able to get a good impression It can be fixed to the point where it is not even close to being a "good fit"
It feels a lot rougher, but so far I haven't encountered any problems
It's a good commercial product depending on how you use it
Also, if it's an Inch-standard car, such as a slightly older Harley or other Inch-standard vehicle, you don't have to mix up the millimeter standards Isn't it good because you can use it?
Since the screw is cut on the Block side, the front fork and the body of the car and the front fork to the Bracket I think you can also use it to extend and install the
In general, I thought it was a good product that hit the itch
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING