* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
Obviously, there's less wind hitting my fingertips, and there's almost no wind in the experience With the outer lower end curved and replaced with our BEET's Handlebar It's completely guarded, but if you're the one who holds the end of the Grip in the OEMHandlebar Small The area around the finger seems to hit the wind In order not to run in conjunction with the Mirror, the hollow of the bracket is replaced by the Screw of the Lever holder but I felt the depressions should have been a little narrower because there was a lot of play
Отличное качество,очень крепкий и плотный материал.Установка занимает очень мало времени,технически просто.Excellent quality, very strong and dense material. Installation takes very little time, it is technically simple.translated by Google TranslatorView Detail
Instructions easy to sort out even though only in Japanese. Some installation advice: 1) I placed the large rubber washers between the bracket and the plastic guard itself. 2) Honda NC mirror stalks are hard to understand! The simplest method is to completely remove the mirror by undoing the top nut and spinning off the mirror - this is LEFT HAND THREAD - so turn your 14mm open-end spanner as if tightening a normal nut. Once the is mirror safely on the bench unbolt the remaining right hand thread bolt from the bar with a ring spanner. Fit the bracket and replace the RHT bolt; tighten. Fit mirror with LHT bolt; tighten while adjusting for view. Much easier this way!Item is good quality (although I might have expected the mounts to be of lighter material eg. aluminium, titanium) and they fit well. Seem to do adequate job of protecting my hands and the looks fit the sporty 700S model well (better than big black buckets).I think I made a good purchase.View Detail
I bought it for winter protection in the Kanto area and never froze when used with winter Gloves, which are not that thick. Installation is also easy, as long as the RightMirror is co-tightened with the Mirror and the RightMirror has an Opposite Thread Screw. The Bracket is solid and the Screen is strong enough to touch. As is the fate of the SR400, the engine vibration is fine but shaky.View Detail
I bought it because I could not stand the strongest cold wave. When I put it on, it didn't look as bad as I thought it would, and I was more than satisfied with the Large effect. The cold wind hitting the fist is reduced, and I think that this is Large sturdy even without Grip heater. It is easy to install and remove, so I recommend it to riders who ride in the middle of winter.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING