* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
Past bij:
YAMAHA WR250R 07-13 *Not available for vehicles equipped with ABS, YAMAHA WR250X 07-12 *Not available for vehicles equipped with ABS
View more
Sub computer is essential if you are changing intake system and exhaust system. As Image it looks like a change in the Jet class of Carburetor Vehicles. Easy to install because it is Couplet-on if Rose even exterior. Even in the state of the basic Map you can change the position you can feel. I am about the same Spec. I felt pretty good with a little change to SPECIAL KnifeMap of acquaintance of acquaintance.
I bought it to get the air/fuel ratio right for my GSX-R1000R. When the engine is installed in the car and the engine is started, the yellow warning light comes on after about 30 minutes. Fail safeMODE. I had a motorcycle shop check it and it was an O2Sensor error. I dismissed the error and asked him to turn off the warning light and start the engine again. But the warning light came on again after about 30 minutes.... The cause was the O2Sensor can Seraa that came with Sub computer. It seems to have gotten heat and is discolored. I called Yoshimura, the distributor of this product, and asked for advice on how to use O2Sensor Can Sera-. They asked me to move it to a better place. It was originally located in a well ventilated area, so the ad-vise is not very useful.... The O2Sensor detects the fuel mapping created by the sub computer as an anomaly, and then the standard The O2Sensor can Seraa is necessary so that I don't have to put it back into state... After all, in my case, I rewrote the ECU and disabled O2Sensor itself. Because fuel mapping was also rewritten, Sub computer became unnecessary and was removed. (I don't know what I'm doing...lol. )。 This Sub computerQuantity:Set the O2Sensor can Sera to Neck.
You can switch MAPs and adjust the sensitivity of the TCs at your fingertips, and it's pretty much just a matter of pulling Wiring It's tedious You can't check the installation place because the memory is too smallView Detail
You need it to create a SelfMap in BAZZAZ We can't talk about it without it If you don't have the knowledge and experience to install and sette Ing, it will be a treasure trove, but you can get the fuel control at the shop If you're going to have it taken away, I think it's a good idea to wear it Once you've decided on a sette Ing, remove it to extend the life of the elementView Detail
YOSHIMURABAZZAZ QS4 USB BZ-Q692Automatic I installed a shifter It's a Level that can be installed in just under two hours It was Striker's Rear Sets, but it was possible to install them with the included Shaft The only thing I would buy is a 10mm Nut
The GSX-S1000 fits until 2016 MODEL, but the GT79B after My Chain The installation was OK with no problem The operation is only Up, but Down has a Slipper clutch, so there is no problem The FI error came out after installation, but it disappeared after learning
When I test drove the car after installation, the sensitivity of Sensor was so good that I felt a close call when I lost fire on a rickety road I did I hurriedly adjusted the sensitivity to reduce the sensitivity After the installation is completed, it seems that the vehicle's gear position needs to be learned and the PC and Maintenance Stand required
Because there is no loss of shift change when accelerating, you can accelerate endlessly
So it was an OK fit for the current MODELView Detail
I chose to buy one without ABS and it had ABS on the outside box I proceeded to work to see if I could do without it, but it should be included in the package (Instruction It's either one of the T-TAPAdapter's or not I'd love to have it I think you should remove the product if this is the caseView Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING